Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices                                                                                                                                   

Please, check our SMD/THT services - smd.lotharek.pl; from idea to ready devices                                                                                                                                   

Shop categories

DivMMC FPGA LITE - PREORDER

PID: LOTH000440


DivMMC FPGA LITE - PREORDER

Our price:

269.00 PLN

Weight: 0.1 kg

Login or register to buy

Buy more, pay less:

  • for 2 pieces and more - 3% (260.93 PLN)
  • for 5 pieces and more - 6% (252.86 PLN)
  • for 10 pieces and more - 9% (244.79 PLN)
  • for 50 pieces and more - 12% (236.72 PLN)
Like Ask Tell

 

 

 

Features

DivTIESUS

Based on DivTIESUS by Miguel Ángel Rodríguez Jódar (open-source version, with some changes).

  • DivMMC compatible, with 8 KiB of EEPROM and 512 KB of RAM. The standard EEPROM flashing utilities from the ESXDOS team work with DivTIESUS.
  • Model autodetection. No jumper or switch is needed to change between a Spectrum 48K and a +3.
  • Own fast clock (28 MHz / 14 MHz), so Bison does not need the CPU clock at all.
  • High-quality push/push MOLEX microSD card slot.
  • Selectable SD card speed (7 MHz / 14 MHz). The default 7 MHz also works with old and cheap SD cards.
  • SLIDE switch tells Bison that the EEPROM can be flashed (JP2 equivalent) and disables automapping.
  • +2A/B/3 all-RAM safe. ESXDOS shadowing does not collide with all-RAM mode. When the system is in all-RAM mode, ESXDOS ROM mapping is disabled.
  • Soft +3E. Bison can load +3E ROM images from the SD card, install them as the system ROM (using its own RAM) and disable automapping (needed for ESXDOS but not for +3eDOS). Your +2A/B/3 then works as a +2e/3e, without opening the case or swapping ROMs. Use the dot command .go3e, which only works with DivTIESUS and Bison.
  • Soft ROM. The same mechanism can load any 16K, 32K or 64K ROM and boot the computer from it (the dot command currently supports 16K ROMs only). Utility and game ROM images can run in their original form, even without a +2A/B/3.

Sound

  • Turbo Sound: 2 × AY-3-8912 (FPGA implementation), with ABC / ACB / mono stereo modes.
  • Soundrive / Covox × 4 channels.
  • Beeper / ULA sound mixed into the audio output (since firmware 1.5 also TAPE OUT).

Joystick

  • Joystick port with 8 modes, including Kempston Mouse. Amiga and Atari ST mice can be used.
  • Joystick mode is selected with the MODE button and stored in the onboard EEPROM. The RESET button and the joystick mode logic are handled directly by the FPGA, with no extra microcontroller.

 

MODE button: joystick mode

Each press of the MODE button switches the joystick interface to the next mode. The change happens instantly, as soon as the button is pressed. Holding the button down does nothing extra; only presses count. You can press quickly several times in a row to skip through modes, and every press is registered.

LEDs: ● on    ● dim    ○ off

# Mode LED 1 · 2 · 3
0 OFF (interface disabled) ○ ○ ○
1 Kempston ● ● ●
2 Sinclair 1 ● ● ●
3 Sinclair 2 ● ● ●
4 Fuller ● ● ●
5 Protek ● ● ●
6 QAOP / Space ● ● ●
7 Kempston Mouse / Amiga ● ● ●
8 Kempston Mouse / Atari ST ● ● ●

After mode 8 it wraps back to OFF.

+2A / +3: When a +2A/+3 is detected (NOTPLUS3 = 0), the modes that emulate the keyboard (Sinclair 1, Sinclair 2, Protek and QAOP/Space) are skipped automatically.

 

Configuration port 4319: audio mode and SD card speed

The AY stereo mode and the SD card speed are not selected with buttons. Instead, a program sets them by writing to I/O port 4319 (0x10DF). You can do it from BASIC, from machine code, or from a small loader or menu program.

Command Setting LED 4 confirmation
OUT 4319,0 Audio: ABC stereo ●  1 blink
OUT 4319,1 Audio: ACB stereo ● ●  2 blinks
OUT 4319,2 Audio: mono ● ● ●  3 blinks
OUT 4319,16 SD card: 14 MHz (fast) fast flicker (~10 Hz) for 1.5 s
OUT 4319,17 SD card: 7 MHz (compatible, default) slow flicker (~3 Hz) for 1.5 s
any other value ignored, no change none

Audio mode

OUT 4319,0 : REM ABC stereo
OUT 4319,1 : REM ACB stereo
OUT 4319,2 : REM mono

Each blink is about 150 ms on and 150 ms off, so the whole confirmation takes 0.3 to 0.9 s. LED 4 blinks even if you select the mode that is already active, so you can always check which mode is set by writing it again.

SD card speed

OUT 4319,16 : REM SD card 14 MHz
OUT 4319,17 : REM SD card 7 MHz (default)

The default 7 MHz works with practically every card, including old and cheap no-name SD cards up to 2 GB that fail at higher speed. Good branded cards can also be used at 14 MHz.

In practice both speeds load files equally fast: the Z80 reads the card byte by byte, and even at 7 MHz the SD interface is several times faster than the CPU. Choose 14 MHz only if you like, and switch back to 7 MHz if a card does not work.

If a card stops working after switching to 14 MHz, just type OUT 4319,17 in BASIC. The command does not need the SD card, so you can always go back.

The speed change is applied between bytes, never in the middle of a transfer, so it is safe to switch at any time.

The port is write-only. Reading it returns nothing, and Bison does not drive the data bus. It is fully decoded on all 16 address bits, so it does not conflict with the ULA, the AY, 128K/+3 paging, the ZX Printer, Interface 1 or the DivMMC.

 

Settings are remembered

The joystick mode, the audio mode and the SD card speed are saved to the onboard EEPROM and restored at power-up. The save happens in the background about 1.5 s after the last change, and only if a setting actually changed. Quickly skipping through several modes therefore causes just one EEPROM write.

LED 4: EEPROM activity

Apart from the audio and SD speed confirmations, LED 4 lights briefly (about 0.3 s) whenever the interface accesses the EEPROM:

When What happens
Power-up Saved settings are read from the EEPROM
~1.5 s after the last change New joystick / audio / SD speed settings are written to the EEPROM

The second flash confirms that your setting has been stored and will be remembered after power-off. If the setting didn't actually change, nothing is written and LED 4 does not flash.

 

Startup animation

After power-up and after every reset, LEDs 1–3 show a short "running light" animation for about 1.2 s. After that they switch to showing the current joystick mode.

The light moves one LED at a time, about 75 ms per step, followed by a short pause with all LEDs off. One full cycle takes about 0.3 s, so it runs about four times.

The direction of the animation shows which machine the interface has detected:

Direction Sequence Machine
Left → right LED 1 → LED 2 → LED 3 → pause 48K / 128K / +2 (NOTPLUS3 = 1)
Right → left LED 3 → LED 2 → LED 1 → pause +2A / +3 (NOTPLUS3 = 0)

Preview

Startup animation, 48K / 128K / +2
48K / 128K / +2
Startup animation, +2A / +3
+2A / +3
Step 1 2 3 4 (pause)
48K / 128K / +2 ● ○ ○ ○ ● ○ ○ ○ ● ○ ○ ○
+2A / +3 ○ ○ ● ○ ● ○ ● ○ ○ ○ ○ ○

Each step lasts about 75 ms; the whole cycle is repeated about four times (≈ 1.2 s).

This gives a quick check at startup that the interface is working and has recognised the machine correctly.

Pressing MODE during the animation still changes the joystick mode, but the LEDs won't show the new mode until the animation ends.


Product gallery


 

 

Producent

LOTHAREK FHU Przemysław Krawczyk
ul. Bukowa 18
42-610 Miasteczko Śląskie, Polska
E-mail: lotharek@lotharek.pl
NIP UE: PL6312246599

Identyfikacja produktu

Identyfikator produktu (PID): LOTH000440
Nazwa produktu: DivMMC FPGA LITE - PREORDER

Pobierz Deklarację Zgodności UE (PDF)

Informacje o bezpieczeństwie

Produkt przeznaczony jest dla użytkowników posiadających podstawową wiedzę techniczną w zakresie montażu i obsługi urządzeń elektronicznych. Przed instalacją lub podłączeniem urządzenia należy odłączyć zasilanie sprzętu, w którym jest ono montowane.

  • Nieprawidłowy montaż może spowodować uszkodzenie urządzenia lub podłączanego sprzętu.
  • Urządzenie nie jest zabawką — przechowywać poza zasięgiem małych dzieci (zawiera małe elementy).
  • Chronić przed wilgocią, wysoką temperaturą oraz wyładowaniami elektrostatycznymi (ESD).
  • W przypadku wątpliwości co do montażu skontaktuj się z nami przed instalacją.
  • Produkt należy użytkować zgodnie z dołączoną instrukcją / opisem na stronie produktu.

Zgodność z przepisami UE

Produkt spełnia wymagania norm RoHS oraz WEEE. Urządzenia elektroniczne i elektryczne nie powinny być wyrzucane razem z odpadami komunalnymi — po zakończeniu eksploatacji należy przekazać je do punktu zbiórki zużytego sprzętu elektronicznego.

Manufacturer

LOTHAREK FHU Przemysław Krawczyk
Bukowa 18
42-610 Miasteczko Śląskie, Poland
E-mail: lotharek@lotharek.pl
EU VAT: PL6312246599

Product identification

Product identifier (PID): LOTH000440
Product name: DivMMC FPGA LITE - PREORDER

Download EU Declaration of Conformity (PDF)

Safety information

This product is intended for users with basic technical knowledge of installing and handling electronic devices. Disconnect power from the host device before installing or connecting this product.

  • Incorrect installation may damage this device or the equipment it is installed in.
  • This is not a toy — keep out of reach of small children (contains small parts).
  • Protect from moisture, high temperature and electrostatic discharge (ESD).
  • If in doubt about installation, please contact us before fitting the device.
  • Use this product only as described in the included instructions / product page.

EU regulatory compliance

This product complies with RoHS and WEEE requirements. Electronic and electrical equipment must not be disposed of with household waste — please take it to an appropriate e-waste collection point at the end of its life.

Hersteller

LOTHAREK FHU Przemysław Krawczyk
Bukowa 18
42-610 Miasteczko Śląskie, Polen
E-Mail: lotharek@lotharek.pl
USt-IdNr.: PL6312246599

Produktkennzeichnung

Produktkennzeichnung (PID): LOTH000440
Produktname: DivMMC FPGA LITE - PREORDER

EU-Konformitätserklärung herunterladen (PDF)

Sicherheitshinweise

Dieses Produkt richtet sich an Nutzer mit grundlegenden technischen Kenntnissen beim Einbau und Umgang mit elektronischen Geräten. Trennen Sie das Zielgerät vor dem Einbau oder Anschluss von der Stromversorgung.

  • Ein fehlerhafter Einbau kann dieses Produkt oder das Zielgerät beschädigen.
  • Kein Spielzeug — von Kleinkindern fernhalten (enthält Kleinteile).
  • Vor Feuchtigkeit, hohen Temperaturen und elektrostatischer Entladung (ESD) schützen.
  • Im Zweifel vor dem Einbau bitte Kontakt mit uns aufnehmen.
  • Nur gemäß beiliegender Anleitung / Produktbeschreibung verwenden.

Konformität mit EU-Vorschriften

Dieses Produkt erfüllt die Anforderungen von RoHS und WEEE. Elektro- und Elektronikgeräte dürfen nicht über den Hausmüll entsorgt werden — bitte geben Sie das Gerät am Ende seiner Lebensdauer bei einer entsprechenden Sammelstelle ab.